XPR-18CL

18,000-lb. Capacity / Two-Post Lift / Clearfloor / Standard Arms
In stock
Only %1 left
SKU xpr-18cl
As low as $15,795.00

If your shop works on massive fleets and vehicles, then you’ll need BendPak’s XPR-18CL. With its 18,000 lb. lifting capacity, it’s one of BendPak’s most extraordinary two-post lift, which means your shop will get the best column, carriage, and frame component construction they offer.


Essential Accessories

  1. BendPak XPR 18CL Heavy Duty Two Post Lift 5175409
  2. +
  3. BendPak WSA 100 Air Electric Work Station
  4. +
  5. BendPak MLS 18 Mobile Jack Stand 5175001
  6. +
  7. BendPak Frame Cradle Pad 60mm Pin 5215761
  8. +
  9. BendPak Offset Pad Adapters 35mm Pin 5601179
  10. +
  11. BendPak Screw Pad Lift 60mm Pin 5215762
Total price: $0.00
  • This item: XPR-18CL $15,795.00
  • MLS-18 $975.00

Overview

The Beast with Two Posts

With the XPR-18CL two-post car lift, you’ll be able to service an incredibly diverse array of vehicles. High-capacity two-post lifts are more commonly known as “all-service” lifts. Since they’re extremely versatile, they’re the most common lift type found in professional shops. Since they’re going to be in many different shops, it was important to BendPak that this lift be able to carry any vehicle that falls under its weight limit. This means the telescoping arms can adjust to fit under race cars and other low ground-clearance vehicles.

In addition to handling smaller cars and light trucks, it will also lift oversized equipment: farming equipment, commercial trucks, etc. BendPak has built the columns wide enough to be able to accommodate just about any vehicle up to 18,000 lbs. making the XPR-18CL perfect for service shops that want to be prepared for just about anything. The only way to get more lifting power would be to start looking at four-post lifts. However, for a smaller footprint, extreme power, and next-level durability and safety, you can’t do much better than the XPR-18CL.

Clearfloor convenience

The XPR-18CL has been designed to allow operators the freedom to move freely underneath the lift, while the hydraulic lines run overhead, safely tucked inside the top crossbeam.

Dual Direct-Drive technology

This lift utilizes two low-pressure HVLP direct-drive cylinders, and as such BendPak has removed the need for lifting chains or screw mechanisms that are commonly found on other lift designs. This direct-drive technology offers better reliability, smoother operation, as well as less maintenance. High-volume and low-pressure equates to less workload placed on the entire hydraulic system.

Industrial-grade hydraulic cylinders

BendPak hydraulic cylinders are made from pilot-fitted, machined steel pistons which are wrapped with specially designed, pressure-loaded U-cup piston seal, backups, and wear bands that don’t allow fluid to bypass back across the tubing. They have crafted the rod out of C-1045/50 micro-alloy steel and plated to a minimum of .001” diametrically. Their high-durometer, mechanically loaded rod seals will prevent rods from leaking, and a urethane rod wiper provides exclusion protection. The cylinder body is welded from high-grade steel that meets/exceeds ASTM specifications.

Super-duty telescoping arms

If you’re thinking of getting an XPR-18CL, it is extremely likely that you’re doing so because you need to service some heavy equipment: garbage trucks, large fleet vans, and more. The telescoping arms on this two-post lift can easily and safely lift up to 15,000 lbs.

Low-profile, dropped-end frame contact pads

Sports cars and low-profile compact vehicles can easily be serviced with the help of the XPR-18CL. BendPak not only raised the lift capacity, but they also managed to keep the ability to service commonly used vehicles. They don’t simply swap light-duty capability for heavy-duty capability.

16-Piece adapter set / standard

Every two-post lift comes standard with BendPak’s 16-piece adapter set, so you won’t have to worry about not being able to reach certain lift points. With this set, you’ll receive eight stackable adapters, four 3” and four 6”, as well as eight cradle pads (four polyurethane pads and four cradle pads). If you’re lifting trucks or vans with running boards or auxiliary fuel tanks, the adapter set is a must-have, and it comes at no additional cost to you.

Lowered arm tube supports

Since the dimensions on the XPR-18CL have been expanded to accommodate larger-type vehicles, BendPak has designed the arm tube supports to be low enough to easily accommodate small vehicles. There’s no point in having a workhorse that handles heavy stuff but not the light stuff, so BendPak made sure that each type handles the same vehicles as their lighter-capacity lifts.

Automatic arm restraints

Heavy vehicles present an increased need for safety features. No one wants to think about what would happen if a lift wasn’t strong enough to hold a dump truck, and let it fall onto your shop’s floor. BendPak eliminates that risk by including extremely powerful auto-locking arm restraints which will engage when the lift goes up, and release when it descends.

Taller lift carriages

BendPak has built their carriages to be 53” high, which in turn makes them safer, more durable, and more efficient. BendPak doesn’t cut corners with their designs.

Maintenance-free load bearings

The XPR-18CL uses durable, reliable, and totally chemical-resistant ultra-high molecular weight polyethylene load bearings which will virtually last forever. Not only are these bearings practically indestructible, you won’t need to lubricate or perform maintenance on these bearings.

Single-piece columns

All of BendPak’s two-post lift columns are made from a single piece of steel in order to better distribute weight down the beam and extend the life of your lift.

Single-point safety release

If you ever have to stop all procedures all you need to do is hit the single-point safety release.

On the level

This lift features a dual-synchro equalization system which will ensure that your two-post lift rises equally no matter what.

Auto shutoff

In the event that any vehicle should touch the overhead structure, the lift will automatically shut off, even if the user keeps trying to raise the lift.

High-speed hydraulics

A few things that make the XPR-18CL one of the fastest lifts in the industry is the fact that it includes 3/8” hydraulic lines, a high-flow pump, and an integrated AC power-unit.

Choose Extended Height

The XPR-18CL-192 is safe and sturdy and features lift columns that are longer than what you’ll find on the standard models, so larger vehicles can be accommodated.

Features

  • 18,000-lb. lifting capacity
  • Padded overhead safety shutoff bar
  • Extended height top-beam provides greater overhead clearance
  • Single-point safety release
  • Dual direct-drive hydraulic cylinders
  • Dual-synchro equalization system for equal lifting
  • Oversized 53" tall carriage for superior strength and durability
  • Electric / hydraulic power system
  • Oversized A36 steel base plates
  • Self-lubricating dura-glide UHMW polyethylene bearing system
  • Safety locks in each column spaced every 3"
  • Plated arm restraints and arm pins for rust prevention
  • Heavy-duty 1/2" aircraft-quality equalizer cables
  • Oversized cable sheave diameter reduces cable fatigue
  • Durable, rubber lift pads with stackable adapters
  • Multi-piece adapter set includes four 6" stackable adapters, four 3" stackable adapters, four polyurethane contact pads and four frame cradle pads. Ideal for trucks and vans with running boards or auxiliary fuel tanks.
  • Convenient storage is included for truck and van adapters
  • Versatile drop-in contact pads with stackable adapters

Specs

SKU# 5175409
Lifting Capacity 18,000 lbs. (8,165 kg)
*Max Capacity / Front Axle 9,000 lbs. (4,082 kg)
*Max Capacity / Rear Axle 9,000 lbs. (4,082 kg)
A - Rise 69" (1,753 mm)
B - Rise + Pad Only 74" (1,880 mm)
C - Rise + Pad + 63 mm Adapter 80" (2,032 mm)
D - Min. Height + Pad 5" (127 mm)
E - Height Overall 170" (4,318 mm)
F - Width Overall 155" (3,937 mm)
G - Outside Columns 144" (3,658 mm)
H - Inside Columns 120" (3,048 mm)
I - Drive-Thru Clearance 106" (2,692 mm)
J - Floor To Overhead Switch 165" (4,191 mm)
K - Front Arm Reach: (MIN) 39" (991 mm)
K - Front Arm Reach: (MAX) 60" (1,524 mm)
L - Rear Arm Reach: (MIN) 39" (991 mm)
L - Rear Arm Reach: (MAX) 60" (1,524 mm)
Max Load Per Arm 4,500 lbs. (2,041 kg)
Motor 220 VAC / 60 Hz / 1 Ph
Noise 45 dB
Weight 2,726-lbs. (1,236 kg)
Dimensions 175'' x 29'' x 34'' (794 mm x 737 mm x 864 mm)
Time to Full Rise 45 seconds

WARNING: California's Proposition 65